Technology and Operations
This forum is for discussing technological & operational matters pertaining to U-boats.
Re: Description of torpedo tubes
Posted by:
SnakeDoc
()
Date: September 29, 2010 06:21AM
Hello Don
Don Prince Wrote:
-------------------------------------------------------
> I hope you don't mind, I printed it for a reference.
Thank you Don, ofcourse not.
> Q1 - Photo 9 shows two holes in the torpedo tube.
> Are these holes the location where compressed air
> enters before and after the piston for submerged
> and surface firings?
I marked these holes on the following image:
[img831.imageshack.us]
I cannot find any good photo of the starboard side of the tube to
see any arrangement corresponding to the "unknown" hole.
When I get next time in Laboe, I'm gonna figure it out.
> Q2 - Was it always required to install the piston
> for a surface attack? Perhaps the piston was
> needed to allign the torpedo so the adjusting
> devices were mated properly?
Yes, the piston was helpful to align while loading, but the main
"device" used to keep torpedo in proper position was stop-bolt.
I remember, that I have read descriptions, that after
depth charges/air bomb attack the tubes were damaged in such way,
that piston could jammed in tube, but torpedo could still be fired.
In such case there were possible surface attack without usage piston.
--
Regards
Maciek
[www.tvre.org]
Don Prince Wrote:
-------------------------------------------------------
> I hope you don't mind, I printed it for a reference.
Thank you Don, ofcourse not.
> Q1 - Photo 9 shows two holes in the torpedo tube.
> Are these holes the location where compressed air
> enters before and after the piston for submerged
> and surface firings?
I marked these holes on the following image:
[img831.imageshack.us]
I cannot find any good photo of the starboard side of the tube to
see any arrangement corresponding to the "unknown" hole.
When I get next time in Laboe, I'm gonna figure it out.
> Q2 - Was it always required to install the piston
> for a surface attack? Perhaps the piston was
> needed to allign the torpedo so the adjusting
> devices were mated properly?
Yes, the piston was helpful to align while loading, but the main
"device" used to keep torpedo in proper position was stop-bolt.
I remember, that I have read descriptions, that after
depth charges/air bomb attack the tubes were damaged in such way,
that piston could jammed in tube, but torpedo could still be fired.
In such case there were possible surface attack without usage piston.
--
Regards
Maciek
[www.tvre.org]
Subject | Written By | Posted |
---|---|---|
Description of torpedo tubes | SnakeDoc | 08/18/2010 11:41PM |
Re: Description of torpedo tubes | Richard Carr | 09/06/2010 03:51PM |
Re: Description of torpedo tubes | SnakeDoc | 09/06/2010 05:09PM |
Re: Description of torpedo tubes | Richard Carr | 09/06/2010 11:10PM |
Re: Description of torpedo tubes | SnakeDoc | 09/07/2010 07:19AM |
Re: Description of torpedo tubes | Don Prince | 09/25/2010 08:36PM |
Re: Description of torpedo tubes | SnakeDoc | 09/29/2010 06:21AM |
Re: Description of torpedo tubes | SnakeDoc | 02/12/2012 09:14PM |
Re: Description of torpedo tubes | elanaiba | 10/01/2010 03:16PM |
Re: Description of torpedo tubes | SnakeDoc | 04/18/2011 08:13AM |
Re: Description of torpedo tubes | von Schoenvorts | 03/30/2012 02:26AM |
Re: Description of torpedo tubes | SnakeDoc | 03/30/2012 10:11PM |
Re: Description of torpedo tubes | SnakeDoc | 02/12/2012 09:16PM |
Re: Description of torpedo tubes | SnakeDoc | 04/08/2013 12:04PM |