Does anyone know that these are?? That they are use for?? Thanks.
Forum: Modeling and schematics

Thanks Ã…kerberg!! I had seen and have this article, I should had check it first
Forum: General Discussions

Does anyone know that happen to the Balcongerät on U 995? It was on U-995 when it arrived at Laboe (around November 1971) but by March 1972 it was missing? Why was it taken off?
Forum: General Discussions

Hi Dan Was it only found in the forward torpedo room? Also were you able to get any "hi res", color, better, photos of it? Simon
Forum: Modeling and schematics

Hi Dave You have PM. Simon
Forum: Modeling and schematics

Forum: General Discussions

U-995, Type VIIC/41 at Laboe U-2540, Type XXI at Bremerhaven
Forum: General Discussions

you have PM
Forum: Modeling and schematics

I believe aft torpedo tube on a Type VII-D is the same for the VIIC and the VIIC/41. I also think the VIIB. If you can find any good pictures of a Type VII's aft torpedo tube, it should do the job.
Forum: Modeling and schematics

Have you check out there are several other great builds here that you may get the information you need. Also that year is your Type VIIC? As the radio anntenna change over time.
Forum: Modeling and schematics

I believe that no good photo's of U-1105 that you can see the tiles, However, you can see real tiling on U-480, it also had Alberich on it. Check out great pictures of it at. There are few more pictures also in this topic
Forum: General Discussions

Is the 800 mm the inter hatch opening or the total diameter?
Forum: Modeling and schematics

In Anatomoy of the ship ~ Type VII on page 95, Figure E10/3. It say "Late Type Schorchel head".... I thought this type of schnorchel was only used on Type XXI. Does anyone know if it was used on any Type VII's?
Forum: Modeling and schematics

Thanks, Evan
Forum: Modeling and schematics

Thanks Chris You can see more of my VIIC/41 at
Forum: Modeling and schematics

Sorry wrong link above here the new one
Forum: Modeling and schematics

Here is the bow section that I have just finish. Happy viewing
Forum: Modeling and schematics

Does anyone have is book, I was wondering what all the little arrows (red circle) on the plating lines mean, like on page 78?
Forum: Modeling and schematics

At the top
Forum: Modeling and schematics

Does anyone have any pictures of the inside of the keel for the Type VII's? I am after any pictures of the frames within the keel. Thanks, Simon
Forum: Modeling and schematics

Just an update on this question, if a few people are wondering After looking at the u-boat plans a little bit more, I believe that the deck height is the same for both the VIIC and the VIIC/41, in fact all the Type VII’s, all but the two non-build boats VIIC/42C and the VIIC/43 as I believe the pressure hull was 100 mm wider on these versions.
Forum: Modeling and schematics

If anyone gets to see this DocO, I would be keen to know and ask a few questions. As I am drawing U-1308. I would be keen to know anything about how the titles looked on the boat, size, layout etc...
Forum: General Discussions

I have just finish completely redrawing the stern part of the hull of my drawing. I have used genuine U-boat measurement base on very precise U-boat plans. That I was very kindly given to me . All the frames, ribbings, ‘frame plate holes’, hydrophone, rudder etc…...almost everything which it part of the hull has exact, wide, length and position base on the plans measurement. However, there
Forum: Modeling and schematics

> P.s. - What does the "NONE-BUILD" Part mean?!? I think that it mean that the VIIC/42 & VIIC/43 were never build. Also you have PM Jonathan Bolz
Forum: Modeling and schematics

Does anyone know if the height between the top of the pressure hull and the deck was greater for the VIIC/41 compare to the VIIC? I measurement the distance and I find that the VIIC/41 is approximately 200 mm higher. Is this correct? Was it higher to make more room for piping etc..?
Forum: Modeling and schematics

Does anyone have any pictures of U-1308 or know if it had a Schnorchel? Thanks, Simon.
Forum: General Discussions

Thanks to all the people that help me with the driving & buoyancy tank question . Below are my new drawings of the stern. PS. I still do not know that the outlet valves look like, if anyone knows would be real keen to draw them correctly.
Forum: Modeling and schematics

Hi Don Thanks for the nice words. If you want, you can see more pictures of my drawing at AMP Forms
Forum: Modeling and schematics

Does anyone know the attachment location on the deck for the Radio Aerial wire to the stern? On U-boat plans they show the wires attaching to just inside the deck edge and all photographs I seen show the wires attaching to the edge of the deck . Which is correct?
Forum: Modeling and schematics

Hi Don I think I may have found the missing inlet vent for the Stern Driving Tank that is found between frame numbers -10 and -11 If you look at all three sterm plans you can make it out. I easiest to see on the VIID plans. Does anyone have any pictures of the very end of the stern, so I can check this?
Forum: Modeling and schematics